HP 8116A Function Generator Tutorial Contents 1 Introduction 1 2 Quick Notes (to get started fast) 1. The HP 8116A is a voltage waveform generator. It can be used to apply periodic voltage waveforms to a circuit (e.g., sinusoids, square waves, triangle waves, and pulses). Pulse: A voltage pulse is sent periodically. The pulse width. HP 8112A Manuals & User Guides. User Manuals, Guides and Specifications for your HP 8112A Pulse Generator. Database contains 1 HP 8112A Manuals (available for free online viewing or downloading in PDF): Operating, programming and servicing manual.
Title & Document Type: A 50 MHz Programmable Pulse Generator This manual may contain references to HP or Hewlett-Packard. Hp A Pdf User Manuals. View online or download Hp A Operating, Programming And Servicing Manual. View and Download HP A operating, programming and servicing manual online. 50 MHz programmable. A Pulse Generator pdf manual download.
- HP 8112A Manuals & User Guides. User Manuals, Guides and Specifications for your HP 8112A Pulse Generator. Database contains 1 HP 8112A Manuals (available for free online viewing or downloading in PDF): Operating, programming and servicing manual.
- Apr 30, 2019 HP 8112A MANUAL PDF - Title & Document Type: A 50 MHz Programmable Pulse Generator This manual may contain references to HP or Hewlett-Packard. Hp A Pdf User Manuals.
- View and Download HP 8116A quick manual online. 50 MHz Pulse/Function Generator Solves More than Everyday Analog Needs. 8116A Pulse Generator pdf manual download. Also for: 8116as.
| Author: | Sasho Balrajas |
| Country: | Senegal |
| Language: | English (Spanish) |
| Genre: | Spiritual |
| Published (Last): | 7 October 2004 |
| Pages: | 111 |
| PDF File Size: | 12.22 Mb |
| ePub File Size: | 5.7 Mb |
| ISBN: | 283-6-90202-624-7 |
| Downloads: | 25724 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Douramar |
Slope IC block diagram Refer to Figure Both functions are performed 70! In the following program, line 20 causes a syntax error so that a SRQ is generated. You can then proceed to the appropriate chapter which covers that function in more detail.
Operating Examples 6. Main Board A1 – Schematic 6 Check the period generator operation against Table If the container or cushioning material is damaged, keep it until the contents of the shipment have been checked for completeness and the instrument has been verified both mechanically and electrically.
The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer, Buyer-supplied software or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance.
The time taken for the HP A to receive and implement a programming message can be divided into three parts: UlC compares the -f5. Set the attenuation factor to and its offset to 0 V. Refer to Figure The required output-offset is created by injecting the offset-input signal from, the offset vernier DAC and the HILC from the timing circuit, into the summing point of the offset-voltage control amplifier via Roffs.
The main amplifier can be divided manjal three stages: You need to allow for this in your controller program.
Address Decoders Refer to Figure Self-test and fault diagnosis are performed each time the instrument is switched on. 1812a HP A from the counter.
HP Hewlett Packard 50 MHz Pulse Generator 8112A
The parameter units are indicated by the LEDs to the right 8112q the display. Main Board A1 – Component layout Add to watch list Remove from watch list.
UID detects this and its output switches toward the negative supply. Visual and Status Byte indication of incompatible settings, under-range control voltage, and clipped amplitude excessive transition time. Delay Generator Operation Slope Error Bit 3 This error is caused by excessive 8112s.
Note More than one error condition can occur at one time. Note The output is not automatically disabled when the program is exited.
Item description Seq which among other things prohibit About half the interior pages are separated from the binder, but does effect readability. Mode Decoder check table Typical signals in Trigger mode 1. Check the ramp signal at pin 20 of U against Figure Duty Cycle Performance Test Linear [y] Permits both the leading and trailing edges of the HP A output pulse to be programmed independently of each other, in the range 6.
Output voltages double when driving a high impedance load. Examine the HP A output on the scope display in order to verify that the pulse characteristics do not exceed 8112x specified limits as identified in Figure As expected, the value of the status byte printed in line 60 will therefore be Waveform Control truth table Adjustment Points on the Main Board A1.
HP A Compatible Pulse Generator – GPH | Marvin Test Solutions, Inc.
Hp 8112a
Set the oscilloscope to display one pulse using the Delta t mode. Power Supply block diagram Refer to Figure Then press the green SETl key. This item will be shipped through the Global Shipping Program and includes international tracking. Interpretation of the command s starts as soon as a valid terminator is 8112x. Then choose value using [Vernier].